Product Description

Stainless Steel Coupling Gear Rigid Roller Chain Fluid Tyre Grid Jaw Spider HRC Nm Motor Flange Gear Pump Rubber Spline Shaft Flexible Universal Joint Coupling

Product Description

Main products
Coupling refers to a device that connects 2 shafts or shafts and rotating parts, rotates together during the transmission of motion and power, and does not disengage under normal conditions. Sometimes it is also used as a safety device to prevent the connected parts from bearing excessive load, which plays the role of overload protection.

Couplings can be divided into rigid couplings and flexible couplings.
Rigid couplings do not have buffering property and the ability to compensate the relative displacement of 2 axes. It is required that the 2 axes be strictly aligned. However, such couplings are simple in structure, low in manufacturing cost, convenient in assembly and disassembly, and maintenance, which can ensure that the 2 axes are relatively neutral, have large transmission torque, and are widely used. Commonly used are flange coupling, sleeve coupling and jacket coupling.
Flexible coupling can also be divided into flexible coupling without elastic element and flexible coupling with elastic element. The former type only has the ability to compensate the relative displacement of 2 axes, but cannot cushion and reduce vibration. Common types include slider coupling, gear coupling, universal coupling and chain coupling; The latter type contains elastic elements. In addition to the ability to compensate the relative displacement of 2 axes, it also has the functions of buffering and vibration reduction. However, due to the strength of elastic elements, the transmitted torque is generally inferior to that of flexible couplings without elastic elements. Common types include elastic sleeve pin couplings, elastic pin couplings, quincunx couplings, tire type couplings, serpentine spring couplings, spring couplings, etc

Coupling performance

1) Mobility. The movability of the coupling refers to the ability to compensate the relative displacement of 2 rotating components. Factors such as manufacturing and installation errors between connected components, temperature changes during operation and deformation under load all put CHINAMFG requirements for mobility. The movable performance compensates or alleviates the additional load between shafts, bearings, couplings and other components caused by the relative displacement between rotating components.
(2) Buffering. For the occasions where the load is often started or the working load changes, the coupling shall be equipped with elastic elements that play the role of cushioning and vibration reduction to protect the prime mover and the working machine from little or no damage.
(3) Safe, reliable, with sufficient strength and service life.
(4) Simple structure, easy to assemble, disassemble and maintain.

How to select the appropriate coupling type

The following items should be considered when selecting the coupling type.
1. The size and nature of the required transmission torque, the requirements for buffering and damping functions, and whether resonance may occur.
2. The relative displacement of the axes of the 2 shafts is caused by manufacturing and assembly errors, shaft load and thermal expansion deformation, and relative movement between components.
3. Permissible overall dimensions and installation methods, and necessary operating space for assembly, adjustment and maintenance. For large couplings, they should be able to be disassembled without axial movement of the shaft.
In addition, the working environment, service life, lubrication, sealing, economy and other conditions should also be considered, and a suitable coupling type should be selected by referring to the characteristics of various couplings.

If you cannot determine the type, you can contact our professional engineer

Related products

Company Profile

Our Equipments

Main production equipment:
Large lathe, surface grinder, milling machine, gear shaper, spline milling machine, horizontal broaching machine, gear hobbing machine, shaper, slotting machine, bench drilling machine, radial drilling machine, boring machine, band sawing machine, horizontal lathe, end milling machine, crankshaft grinder, CNC milling machine, casting equipment, etc.
Inspection equipment:
Dynamic balance tester, high-speed intelligent carbon and sulfur analyzer, Blochon optical hardness tester, Leeb hardness tester, magnetic yoke flaw detector, special detection, modular fixture (self-made), etc.

Machining equipments
Heat equipment

Our Factory
Application – Photos from our partner customers

Company Profile
Our leading products are mechanical transmission basic parts – couplings, mainly including universal couplings, drum gear couplings, elastic couplings and other 3 categories of more than 30 series of varieties. It is widely used in metallurgical steel rolling, wind power, hydropower, mining, engineering machinery, petrochemical, lifting, paper making, rubber, rail transit, shipbuilding and marine engineering and other industries.
Our factory takes the basic parts of national standards as the benchmark, has more than 40 years of coupling production experience, takes “scientific management, pioneering and innovation, ensuring quality and customer satisfaction” as the quality policy, and aims to continuously provide users with satisfactory products and services. The production is guided by reasonable process, and the ISO9001:2015 quality management system standard is strictly implemented. We adhere to the principle of continuous improvement and innovation of coupling products. In recent years, it has successfully developed 10 national patent products such as SWF cross shaft universal coupling, among which the double cross shaft universal joint has won the national invention patent, SWF cross shaft universal coupling has won the new product award of China’s general mechanical parts coupling industry and the ZHangZhoug Province new product science and technology project.
Our factory has strong technical force, excellent process equipment, complete professional production equipment, perfect detection means, excellent after-sales service, various products and complete specifications. At the same time, we can provide the design and manufacturing of special non-standard products according to the needs of users. Our products sell well at home and abroad, and are trusted by the majority of users. We sincerely welcome friends from all walks of life at home and abroad to visit and negotiate for common development.p

  /* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

What are the best practices for installing a mechanical coupling correctly?

Proper installation of a mechanical coupling is essential to ensure its optimal performance and prevent premature failure. Follow these best practices when installing a mechanical coupling:

1. Clean the Shaft Ends:

Before installation, ensure that the shaft ends are clean and free from dirt, debris, and any old coupling remnants. Clean the shafts using a suitable solvent if necessary.

2. Verify Shaft and Bore Dimensions:

Check the dimensions of the shaft and bore to ensure they match the coupling’s specifications. Ensure that the shaft and bore diameters, keyway sizes, and lengths are correct for the specific coupling.

3. Lubricate Contact Surfaces:

Apply a thin layer of appropriate lubricant to the contact surfaces of the shaft and coupling bore. This helps in easy installation and minimizes the risk of galling or damage during assembly.

4. Align Shaft and Coupling:

Align the shafts and coupling properly before installing. Avoid forcing the coupling onto the shaft; it should slide smoothly into position.

5. Use Proper Installation Tools:

Use the recommended installation tools or methods provided by the coupling manufacturer. Using improper tools may lead to damage or misalignment of the coupling.

6. Tighten Fasteners Gradually and Evenly:

If the coupling uses set screws, bolts, or any fasteners, tighten them gradually and evenly in a criss-cross pattern. This ensures uniform distribution of pressure and prevents distortion.

7. Check for Proper Keyway Fit:

If the coupling utilizes keyways, ensure that the keys fit snugly into both the shaft and the coupling keyway to prevent movement or slippage.

8. Verify Proper Torque:

If the coupling requires a specific torque value for installation, use a torque wrench to achieve the correct tightening. Avoid over-torquing as it may damage the coupling or cause premature wear.

9. Inspect for Runout and Alignment:

After installation, inspect the coupling for runout and alignment. Verify that the shafts are concentric and parallel, as misalignment can lead to premature coupling failure.

10. Conduct Regular Inspections:

Perform regular inspections and maintenance of the coupling during its operational life. Check for signs of wear, misalignment, or damage and address any issues promptly.

Adhering to these best practices ensures that the mechanical coupling is installed correctly and operates as intended. Proper installation increases the coupling’s longevity, minimizes the risk of downtime, and contributes to the overall efficiency and reliability of the mechanical system.

“`

Can mechanical couplings handle reversing loads and shock loads effectively?

Yes, mechanical couplings are designed to handle reversing loads and shock loads effectively in various applications. Their ability to accommodate these dynamic loads is dependent on their design and material properties.

Reversing Loads:

Mechanical couplings can handle reversing loads, which are loads that change direction periodically. When the direction of the applied torque changes, the coupling must be able to smoothly transition from one direction to the other without any slippage or backlash. Many types of mechanical couplings, such as gear couplings and disc couplings, are well-suited for reversing loads due to their rigid and positive engagement designs. They can maintain a strong connection between shafts and provide reliable torque transmission even during frequent load reversals.

Shock Loads:

Shock loads are sudden, high-intensity loads that occur due to impacts, starts, or stops. Mechanical couplings are engineered to withstand shock loads and prevent damage to the connected equipment. Flexible couplings, like elastomeric couplings, are particularly effective at dampening shock loads. The elastomeric material absorbs and dissipates the energy generated by the impact, reducing the transmitted shock to the system. Some metal couplings, such as beam couplings and bellows couplings, also have good shock absorption capabilities due to their design and material properties.

It’s important to consider the specific application requirements when selecting a coupling for systems with reversing loads or shock loads. Different coupling types have varying capabilities in handling these dynamic loads. Properly choosing a coupling that matches the load conditions ensures the longevity and reliability of the mechanical system, preventing premature wear and failures.

“`

How does a mechanical coupling facilitate the connection between two shafts?

A mechanical coupling plays a critical role in connecting two shafts in a mechanical system and enabling the transmission of torque and motion between them. The process of how a mechanical coupling facilitates this connection can be explained as follows:

1. Physical Linkage:

A mechanical coupling physically links the two shafts together. It consists of two mating components that fit over the respective shaft ends, ensuring a secure connection.

2. Torque Transmission:

When the motor or driving shaft rotates, it generates torque. This torque is transmitted through the mechanical coupling to the driven shaft, causing it to rotate as well.

3. Keyways or Spline Connection:

Many mechanical couplings use keyways or splines to enhance the connection between the shafts. Keyways are slots cut into the shaft and coupling, and a key is inserted to prevent relative motion between the two components.

4. Compression or Expansion Fit:

In some couplings, the connection between the shafts is achieved through a compression or expansion fit. The coupling is designed to be slightly smaller or larger than the shaft diameter, creating a tight fit when assembled.

5. Set Screws or Bolts:

Set screws or bolts are often used in mechanical couplings to secure the coupling tightly to the shafts. These screws apply pressure to prevent any relative movement between the coupling and the shafts during operation.

6. Flexible Elements:

Flexible couplings feature elements made of materials like rubber or elastomers that can bend or flex. These elements accommodate misalignment between the shafts while maintaining the connection and transmitting torque.

7. Key Features:

Certain types of couplings, such as gear couplings or disc couplings, utilize teeth or gear features to achieve a strong and precise connection between the shafts. These key features ensure a positive engagement, enhancing torque transmission.

In summary, a mechanical coupling serves as the link between two rotating shafts, enabling them to function together as a single unit. Whether through a tight compression fit, keyways, or flexible elements, the coupling ensures a secure and efficient connection, allowing torque to be transmitted from one shaft to the other, and enabling the mechanical system to perform its intended function reliably.

“`

editor by CX 2024-04-08